manualshive.com logo in svg

Honeywell TELEPHONE ACCESS MODULE W8735D, Owner'S Manual, Page: 9 / 36

Share
Download
Honeywell TELEPHONE ACCESS MODULE W8735D Owner'S Manual Download Page 9

9

69-2028—01

ACKNOWLEDGING ALERT MESSAGES

You hear “

To acknowledge receipt of this alert 

message, press the # key

.”

After the alert message is announced, the TAM 

prompts you to acknowledge the message. If there is 

more than one active alert message, the TAM 

announces the next message, and continues until all 

alerts are announced.

NOTE: When you acknowledge the alert message by 

pressing the # key, you are clearing the dial-in 

alert message and also clearing the dial-out 

alert. You are 

not

 correcting the condition that 

caused the alert.

IMPORTANT

Pressing any other key (besides the # key) 

ignores the acknowledgement so it remains an 

active alert. The TAM continues to dial out until 

an acknowledgement is received.

IMPORTANT:

After receiving an alert, it is important to take 

appropriate action immediately. See “Alert 

Menu” on page 15 for more information on dial-

out alerts.

Once all alerts are announced, the TAM announces 

the current date, time, outdoor temperature and 

indoor relative humidity (if available).

Outdoor High 

Temperature Limit

The outdoor temperature exceeded the 

high limit setting

Air filter

Air/duct filter needs changing

Humidity Low Limit

The indoor humidity dropped below the 

low limit setting

Humidity High Limit

The indoor humidity level exceeded 

the high limit setting

System Failure

•

An HVAC system component may 

have failed

•

A communications fault may have 

occurred (the communications bus 

may be down)

Table 1. Alerts (Continued)

Alert

Description

Summary of Contents for TELEPHONE ACCESS MODULE W8735D





































Reviews:

No comments