Honeywell SmartPAC 2 User Manual Download Page 97

Page: 97 / 522

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 75

Table 2 - 3. Resolver Wiring on SmartPAC 2

PIN # on TB101

Wire Color

Shield

[terminate to ground stud

nearest entry to enclosure]

212 (GND)

no connection

213 (S1)

Black*

214 (S2)

Green

215 (R1)

Red

216 (S3)

Yellow*

217 (R2)

Orange

218 (S4)

Brown

* Shown for clockwise rotation, facing shaft.
For counterclockwise, swap black and yellow wires

Connecting Communications Between SmartPAC 2 and WPC

Locate TB105 on the SmartPAC 2 board (Figure 2 - 39, page 162) and TB501 on the
WPC Interface Board (Figure 2 - 38, page 161). See Figure 1 at the end of this manual
for wiring.

Run the four-conductor shielded cable through the same flexible liquid-tight

low-

voltage

conduit (referenced above) from SmartPAC to WPC.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartPAC 2

Reviews:

Honeywell SmartPAC 2, User Manual, Page: 97 / 522

Search results

Summary of Contents for SmartPAC 2

Reviews: