manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 87 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 87

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 65

NOTICE

In Inch mode, you can run a complete stroke without causing an Interrupted Stroke.
Interrupted stroke is caused only when you release your hands from the run/inch buttons in
the middle of the stroke.  If you inch the entire stroke without releasing your hands, no
Interrupted stroke is caused.

For more detail, see “Switch 8 – Top Stop Mode for F and H Errors and Auxiliary 1
Response to Interrupted Stroke,” page 248.  For wiring, see wiring diagram Figure 3 at the
end of the manual.

Wiring Auxiliary 2 Output (Optional)

DANGER

!

NON-SAFETY OUTPUTS USED FOR SAFETY FUNCTIONS

Use auxiliary outputs 1, 2 and 3 for non-safety functions only.  They cannot protect
personnel from a moving hazard.  You can use them for convenience in automation.

Failure to comply with these instructions will result in death or serious injury.

The auxiliary 2 in WPC (pin #36) is normally “OFF” and turns “ON,” whenever there is an
Interrupted Stroke or there is a fault condition present.  Also while inching in INCH stroke,
auxiliary 2 stays “ON.” See page 364 for more information about Interrupted Stroke.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments