manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 71 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 71

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 49

6.06

(154.0)

MUTE

RESET

MUTE

EMERGENCY

STOP

PALM

TIME

PRIOR

ACT

TOP

STOP

16.75

(425.5)

28.75

(730.3)

5.50

(139.7)

4.69

(119.1)

Figure 2 - 10.  Operator Station, Top Buttons

Using a Light Curtain on Your Press

DANGER

!

OPERATOR CAN STAND BETWEEN LIGHT CURTAIN AND PINCH POINT

•

Mount the light curtains and operator station according to the instructions in this manual.

•

Mount the operator station outside the area protected by the light curtains.

•

DO NOT mount the operator station between the light curtain and the pinch point.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

INCORRECT LIGHT CURTAIN INSTALLATION

•

Mount the light curtains at the correct safety distance as instructed in this manual.  See
“Calculating the Safety Distance,” page 348, under "Brake Monitor" in Chapter 6.

•

  The light curtain will only provide full protection for operators when mounted at the correct

safety distance.

•

Install and wire your light curtains correctly, following the instructions in your Shadow
manual.

Failure to comply with these instructions will result in death or serious injury.

If you are using light curtains on your press, they must be mounted at least the correct safety
distance away from the hazardous area.  This ensures that the light curtain will send a stop
command to the press in time for the press to stop before anyone can reach the pinch point. If

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments