manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 68 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 68

1126800 

SmartPAC 2 with WPC Integration

Page 46

Chapter 2

Installing SmartPAC 2 and WPC

Wiring the Overrun Sensor Magnetic Switch

NOTICE

You can run both the resolver wires and the overrun limit switch cable through the same
conduit.  If you do this, wait to cut the cable and wires until both the resolver and the overrun
limit switch are installed.

Run the magnetic switch’s cable through conduit to the WPC.  Connect the wires to terminal
blocks on the WPC control board, as shown in the table below.  See also the Figure 3 wiring
diagram at the end of the manual.  You will install the overrun sensor magnet as part of the
initialization process, after you finish the installation procedures in this chapter.

Table 2 - 1.  WPC Overrun Sensor Magnetic Switch Wiring

Pin # 

Connection

Wire color

23

+24 VDC

Red

24

Overrun input to WPC

White or Clear

25

Ground

Black

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments