manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 461 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 461

SmartPAC 2 with WPC Integration

1126800

SmartPAC Preventive Maintenance

Appendix B

page 439

(PM) Monitor

Table B - 1.  Preventive Maintenance Items

air rotary seals

back shaft bearing (1 through 4)

brake

bull gear

clutch valve

conveyor (1 through 6)

counterbalance system

drive belts

DSV

feeder

flywheel bearing

gibs

lube filter

lube motor

lube system

main bearing (1 through 4)

main motor

oil level

pilot solenoid

pinion key

pitman bearing (1 through 4)

"Custom" name

Table B - 2.  PM Tracking Units

run hours

1

days

weeks

months

die changes

ch. cycles (1 through 16)

2

F## WPC press control faults (#: 45 - 59)

3

press overloads

4

1 For SmartPAC (without WPC), "run hours" refers to the length of time that SmartPAC is "on.”  For SmartPAC
with WPC, it means how long the motor is "on.”  (The version of SmartPAC that you currently have is without
WPC.  Contact Wintriss Tech Support if you require WPC.)
2 Ch. cycles 1 through 16 can be used only if you have a 16-channel ProCamPAC. Only ch. cycles 1 through 8
can be used for an 8-channel configuration.
3 These are only available if you have SmartPAC with WPC and if you have wired and assigned press functions
to the user-definable inputs.  (The version of SmartPAC that you currently have is without WPC.  Contact
Wintriss Tech Support if you require WPC.)
4 "Press overload" is only available with AutoSetPAC option.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments