manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 399 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 399

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Run Mode

Chapter 6

page 377

Operating the Press in Continuous On Demand
Mode

DANGER

!

IMPROPER SAFEGUARDING

Ensure that the machine guarding system is installed and maintained according to OSHA
standard 1910.217, ANSI B11.1, ANSI B11.19 and any other regulations and standards that
apply.  Ensure that guarding is properly installed to prevent access to the machine over,
under or around any guarding device.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

PRESS STARTING UNEXPECTEDLY

Ensure that light curtains and other safeguards are properly installed and operating to
protect operators when using Continuous on Demand mode, in which a stroke can occur
unexpectedly.

Failure to comply with these instructions will result in death or serious injury.

For information on using this mode, contact Wintriss Tech Support.

To set Prior Act timing for continuous on demand, see “Switch 5 – Prior Act Timing for
Automatic Single Stroke and Continuous on Demand,” page 245.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments