manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 388 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 388

1126800 

SmartPAC 2 with WPC Integration

Page 366

Chapter 6

SmartPAC 2 Run Mode

Operating the Press in INCH mode

DANGER

!

IMPROPER SAFEGUARDING

Ensure that the machine guarding system is installed and maintained according to OSHA
standard 1910.217, ANSI B11.1, ANSI B11.19 and any other regulations and standards that
apply.  Ensure that guarding is properly installed to prevent access to the machine over,
under or around any guarding device.

Failure to comply with these instructions will result in death or serious injury.

DANGER

!

INCH MODE NOT SUITABLE FOR PRODUCTION

DO NOT use INCH mode as a production mode, per ANSI B11.1–2001.

Failure to comply with these instructions will result in death or serious injury.

Three Ways You Can Operate the Press in INCH Mode

You can choose three different ways to operate the press in INCH mode,

Top Stop in Inch Enabled, page 367

Top Stop in Inch Disabled (Top Stop Bypass), page 367
Micro-inch, page 367

Pin 13 on the WPC board controls whether the press top stops in Inch mode.

See “Press Options,” page 241 in Chapter 4 for how to make the settings for these operating
modes.  This is how you operate the press in each mode.

NOTICE

These steps assume that you are running in TWO HAND mode.  If you run in ONE HAND
mode, you need to depress only the left RUN/ INCH switch (unless the operator station has
an optional right/ left hand selector switch).

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments