manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 384 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 384

1126800 

SmartPAC 2 with WPC Integration

Page 362

Chapter 6

SmartPAC 2 Run Mode

F1

F2

F3

F4

F5

F6

F7

F8

Figure 6 - 30.  Messaging, Select Message

4.

 

Use the cursor keys to highlight the message you want to send.  Press 

F4

-“Select

Message” to select the message.  The message appears next to “Message:” at the top of
the screen.

5.

 

To send the message, Press 

F5

-“Send Message and Exit.”  If you do not want to send the

message, press 

F6

-“Exit Without Sending.”

For HELP press the HELP key located at the center of the cursor (arrow) keys.

Send E-mail to Wintriss Tech Support

If you select Wintriss Tech Support as your recipient, and Error Log Files as your message,
the Tech Support receives a message that looks something like the following figure.  In
addition to including files of error logs, it lists the installed options and other useful
information.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments