manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 380 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 380

1126800 

SmartPAC 2 with WPC Integration

Page 358

Chapter 6

SmartPAC 2 Run Mode

Figure 6 - 24.  Next Tool Number Display

1.

 

Perform one of the following:

•

 

To load the tool shown, press ENTER and go to the next step.

•

 

To load a different tool, press RESET and go to the next section, “Select a Tool to
Load.”

2.

 

At the “Next Tool” display, shown in the previous figure, press ENTER.  A warning box
appears similar to the following:

Figure 6 - 25.  Load Tool Warning Box

•

If you want to load the tool, press ENTER.  A message appears, saying “Tool
Number  Is Being Loaded” while SmartPAC 2 loads the tool.  The display returns to
the main Run menu and the tool number you just loaded appears in the status box.

•

If you do not want to load the tool, press RESET.  The display returns to the main
Run menu.

NOTICE

If you tried to load the tool, and got an error message instead of the “Tool Number Being
Loaded” message, go to Chapter 7 and find the section describing that error message.
Follow the instructions there for correcting the problem. If the error message is not described
there, or you cannot fix the problem, contact Wintriss Tech Support, and be ready to provide
some important information to expedite a resolution to the problem.  Please supply:  product
name (e.g. SmartPAC 2 standard); installed options (e.g. DiProPAC, ProCamPAC, etc.); and
firmware version number (e.g. Vs. 2.00).  You can determine the last two items, by going into
"Installed options" in the Initialization mode (see Chapter 4 for details).

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments