manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 377 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 377

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Run Mode

Chapter 6

page 355

TOOL INFORMATION (Optional)

(RUN – TOOL INFORMATION)

NOTICE

•

Tool Information serves only as a convenient place to record information about the tool.  It
does not control any aspect of press operation.

•

This feature is not available if you have the optional PLC interface installed.

•

If SmartPAC 2 is connected to PACNet computerized pressroom reporting, “Display the Next
Tool” may appear at function key 

F4

.  See the PACNet manual for more information.

If you have this option, select “Tool Information” from the Run menu (Figure 6 - 1) to
change the information about the tool you are using.  (See “Tool Information” in Chapter 5.)
You will see a display similar to the following.

F1

F2

F3

F4

F5

F6

F7

F8

Figure 6 - 22.  Tool Information Screen

“Display the Next Tool” available only with PACNet Software

ARE YOU LOCKED OUT?

Access to changing the information on this screen may be limited to Program mode or may
require a password.  The security access settings in the Initialization menu determine when
changes can be made.  

See 

“Security Access” in Chapter 4, page 251.

To enter information about the items:
1. Select the desired item.  A screen overlay appears in which you can enter the appropriate

value.  For Yes/no items, enter 0 (zero) for NO, and 1 (one) for YES.

2. Enter text into the memo box, by pressing

 F5

 for the first line, and 

F6 

for the second

line.  A screen overlay appears that enables you to enter fifteen characters of numbers
and alphabetic text for each line.  When you complete each line, press 

F6

 to accept it.

3. When you have finished entering information into the tool number information screen,

press RESET to return to the main Programming menu.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments