Honeywell SmartPAC 2 User Manual Download Page 365

Page: 365 / 522

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Run Mode

Chapter 6

page 343

View Global Cam Summary

(RUN – CAM SWITCH –

-VIEW GLOBAL CAM SUMMARY)

NOTICE

Find instructions for running the press at the end of this chapter, starting on page 364.

NOTICE

If you set or changed global cams while a tool was loaded, you must reload the tool to make
the global cams take effect.

You can also view a summary of the Global cams by pressing

-“View Global Cam

Summary.” A screen similar to the following appears, listing the channel number, cam
name, type and ON/OFF or time setting.

Figure 6 - 16. Viewing Global Cams

NOTICE

To e-mail a copy of this screen, see “Screen Capture,” page 199.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartPAC 2

Reviews:

Honeywell SmartPAC 2, User Manual, Page: 365 / 522

Search results

Summary of Contents for SmartPAC 2

Reviews: