manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 315 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 315

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Program Mode

Chapter 5

page 293

number of
strokes for
DiProPAC
to auto
enable ALL
sensors in
the tool

10

AUTO ENABLE COUNTER FOR THIS

STROKES

USE THE CURSOR KEYS TO CHANGE THE NUMBER
OF STROKES.  PRESS THE ENTER KEY WHEN
DONE.  PRESS THE RESET KEY TO CANCEL.

TOOL NUMBER 1234567
CHAIR BRACKET

TOOL IS

AUTO ENABLE COUNTER DETERMINES HOW MANY
STROKES THE SENSORS CAN BE DISABLED AT
A TIME.  THEY ARE AUTOMATICALLY ENABLED
AFTER REACHING THE COUNT.

Figure 5 - 17.  Setting "Auto Enable by Tool" Counter

3. Next you will see a list of sensors to program.

SENSOR 2
SENSOR 3
SENSOR 4
SENSOR 5
SENSOR 6
SENSOR 7
SENSOR 8
SENSOR 9
SENSOR 10
SENSOR 11
SENSOR 12
SENSOR 13
SENSOR 14
SENSOR 15
SENSOR 16

USE CURSOR KEYS TO
CHOOSE A SENSOR.
PRESS THE ENTER KEY
TO PROGRAM. PRESS THE
RESET KEY WHEN DONE.

TOOL #1234567
CHAIR BRACKET

SENSOR 1

Figure 5 - 18.  List of sensors to program

NOTICE

We are illustrating a 16-sensor DiPro module.  Depending upon the way that  your
SmartPAC 2 has been configured (with DiPro 8 sensors or with DiPro 16 sensor), your
display may vary.

4. You can select any sensor, but it is a good idea to start with the first sensor. Select

"sensor 1.” After selecting it, the first thing you do is name it.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments