manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 279 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 279

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Initialization Mode

Chapter 4

page 257

Additional Security

You can secure your WPC adjustments by installing a user-supplied keylock switch.  For
installation instructions, see page 66, “Wire a Keylock Switch to Prevent changes to WPC
Settings.”   The switch works as follows:

•

Switch CLOSED (grounded): prevents changes to any WPC settings in Program and
Run modes

•

Switch OPEN (not grounded):  Normal operation of  Program and Run modes.

By using this keylock switch, you can prevent anyone from making changes to WPC settings
in Program mode and Run mode.  This keylock switch overrides the Security Access settings
discussed in the previous sections.
Here are the messages that you will see in SmartPAC's Program and Run modes when the
keylock switch is closed at input 1.

message indicating

selected operating

mode is locked

TOP STOP ANGLE
MAX. PRESS SPEED
MIN. PRESS SPEED
CNTR BAL SETPOINT

270
200
150

40

DEGREES
SPM
SPM
PSI

THE PRESS CONTROL EDIT MODE IS LOCKED.
PRESS THE RESET KEY WHEN DONE.

PRESS CONTROL PARAMETERS

TOP STOP ANGLE
MAX. PRESS SPEED
MIN. PRESS SPEED

270
200
150

PRESS CONTROL ADJUST MENU

DEGREES
SPM
SPM

TOOL NUMBER 1234567        PART CNTR        0
CHAIR BRACKET                    TWO HAND INCH
SENSORS ENABLED

SETPOINT PRESSURE (PSI)

COUNTER. BAL
MAIN AIR

40
60

36
65

THE PRESS CONTROL EDIT MODE IS LOCKED.
PRESS THE RESET KEY WHEN DONE.

270

270

Figure 4 - 38.  Press Control Adjustments Locked

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments