Honeywell SmartPAC 2 User Manual Download Page 242

Page: 242 / 522

1126800

SmartPAC 2 with WPC Integration

Page 220

Chapter 4

SmartPAC 2 Initialization Mode

Enabling or Disabling Setup Mode

(INITIALIZATION - SENSOR ENABLE MODE)

NOTICE

If your SmartPAC 2 is

not

integrated with a WPC, your inch-selector switch must be wired to

the setup mode input, terminal #252 on TB107.

If you enable Setup mode, the green sensors are disabled in the condition you choose:

•

In Inch mode
or

•

In Inch mode

and

in Interrupted-stroke mode. (Available only with WPC integration)

For more information, see the Initialization chapter in your user manual.

1. To enable or disable Setup mode, in the Main Initialization menu, select SENSOR

ENABLE MODE.

MAIN INITIALIZATION MENU

USE THE CURSOR

RESOLVER ZERO

KEYS TO CHOOSE

POSITION SENSOR

MENU ITEMS. PRESS INSTALLED OPTIONS
THE ENTER KEY TO

SELECT CAM NAMES

SELECT. SWITCH TO AUTO ADVANCE
RUN WHEN DONE.

CUSTOM SENSOR NAMES
SENSOR ENABLE MODE
PROCESS MONITOR
TOOL INFORMATION
RAMPAC INIT
PRESS CONTROL
SECURITY ACCESS

SENSOR ENABLE MODE

Figure 4 - 15. Main Initialization Menu

A screen similar to the following appears.

DIE PROTECTION MODE SELECTION MENU

SENSOR ENABLE MODE = AUTO BY TOOL
SETUP MODE = DISABLED

USE THE CURSOR KEYS TO SELECT THE MODE
YOU WANT TO CHANGE. PRESS THE ENTER KEY
TO CHANGE IT. PRESS THE RESET KEY WHEN
YOU ARE DONE.

DISABLED

Figure 4 - 16. Setup Mode Status

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartPAC 2

Reviews:

Honeywell SmartPAC 2, User Manual, Page: 242 / 522

Search results

Summary of Contents for SmartPAC 2

Reviews: