manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 231 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 231

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Initialization Mode

Chapter 4

page 209

INSTALLED OPTIONS

(INITIALIZATION – INSTALLED OPTIONS)

This is a very useful display that indicates how your SmartPAC 2 has been configured.  It
includes firmware version numbers and the specific optional capabilities that have been
installed.  It also tells you how many cam channels and/or sensors you can connect to
SmartPAC 2.  The following figure shows an example of a list of installed options.

Figure 4 - 5.  List of Installed Options

Your screen will look different.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments