manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 195 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 195

SmartPAC 2 with WPC Integration

1126800

SmartPAC 2 Keyboard, Displays

Chapter 3

 Page 173

and Operating Modes

Comparing SmartPAC 2 with Original SmartPAC

If you are familiar with the original SmartPAC, you will find using the SmartPAC 2 very
similar.  The figure below shows the differences between their front panels.  Some of the
instructions in this manual are based on those for the original SmartPAC.

ENTER

RESET

PROG

RUN

OFF

INCH

SINGLE

STROKE

CONT

POWER

BRAKE

WARNING

HELP

1 2 3
4 5 6

9

8

7

.

0

CLEAR

SmartPAC 2

F1

F2

F3

F4

F5

F6

F7

F8

CAMBIE

AL ESPANOL

USE THE CURSOR KEYS

ENABLE SENSORS

TO MAKE SELECTIONS.

COUNTERS

PRESS ENTER TO 

CAM SWITCH

ACCESS SELECTION.

BRAKE MONITOR
TONNAGE/WAVEFORM
PROCESS MONITOR
FEED CONTROL
PM MONITOR
TOOL INFORMATION
SHUTHGT/CNTRBAL
ERROR LOG
LOAD NEW TOOL
DIALOG MENU
TOGGLE HOT KEYS 1

330

PRESS # 14

TOOL NUMBER  6160

PART CNTR 0

FLANGE  

TWO HAND S.S.

INTERRUPTED STROKE

PRESS ANGLE  330

1

4

7

2

3

5

6

8

9

0

.

CLEAR

Contrast

CURSOR

INTERRUPTED

STROKE

BRAKE

WARNING

ENTER

RESET

F1

F2

F3

F4

F5

F6

Wintriss Press Automation Control

SmartPAC

PROG

RUN

ENABLE SENSORS
COUNTERS
DIE PROTECTION
CAM SWITCH
TOOL INFORMATION
RAM POSITION
RAM TONNAGE
ERROR LOG
LOAD NEW TOOL

USE THE CURSOR KEYS
TO MAKE SELECTIONS.
PRESS ENTER TO
ACCESS SELECTION

TOOL NUMBER 6160                PART CNTR  0
CHAIR BRACKET

ENABLE SENSORS

Crank Angle/SPM display

8 Function keys

6 Function keys

Help key

SmartPAC 2

only

Contrast keys

original SmartPAC

only

SmartPAC 2 with WPC Integration

OFF

INCH

SINGLE

STROKE

CONT

OFF

INCH

SINGLE

STROKE

CONT

Interrupted Stroke Indicator

original SmartPAC only

Interrupted Stroke Message

SmartPAC 2 only

Original SmartPAC with WPC Integration

Figure 3 - 2.  Differences Between SmartPAC 2 and Original SmartPAC

SmartPAC 2 and the original SmartPAC are very similar in appearance and many of the
procedures for using them are the same.  Note these differences:

Item

SmartPAC 2

Original SmartPAC

Crank Angle/SPM display

In the center of the Crank Angle
clock on the display and in the
status box at the top of the display.

Separate red LED 3-digit display

Function Keys

8 function keys

6 function keys

Help Key

At center of cursor keys;
press to access information
relating to the current screen.

None

Contrast keys

None – display is self-adjusting

2 to left of display screen

Interrupted Stroke
Indication

Message flashing in status box at
the top of the display

Indicator light on front panel

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments