manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 193 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 193

SmartPAC 2 Keyboard, Displays

Chapter 3

page 171

and Operating Mode
SmartPAC 2 with WPC Integration

1126800

Chapter 3 – SmartPAC 2 Keyboard,
Displays and Operating Modes

This chapter tells how to use the SmartPAC 2 keyboard and displays. This chapter gives you
the basics for getting started.  Later chapters explain in more detail how to use the different
operating modes in SmartPAC 2.

It is a good idea to learn how to use the SmartPAC before you install it.  Set up the unit on a
bench and wire a power cord and a resolver to it, so you can try making settings.

Read this chapter to become familiar with the keyboard and displays. Then try going through
the menus and making settings.  You will find it is easy to use SmartPAC 2.  The instructions
on the display tell you which key to press in order to proceed to the next step. After you learn
how, you will find it very fast and easy to make settings.

While you are learning how to use SmartPAC 2, do not be afraid to try things. Push the keys.
Select items on the displays. See what happens. You cannot hurt SmartPAC 2 by pushing a
wrong key or making a wrong selection.

SmartPAC DEMO

TOOL NUMBER  6160

PART CNTR 0

DEMO TOOL

TWO HAND S.S.
FLYWHEEL SPM    67

CAMBIE

AL ESPANOL

USE THE CURSOR KEYS

ENABLE SENSORS

TO MAKE SELECTIONS.

COUNTERS

PRESS ENTER TO 

CAM SWITCH

ACCESS SELECTION.

BRAKE MONITOR
TONNAGE/WAVEFORM
PROCESS MONITOR
FEED CONTROL
PM MONITOR
TOOL INFORMATION
SHUTHGT/CNTRBAL
ERROR LOG
LOAD NEW TOOL
DIALOG MENU
TOGGLE HOT KEYS 1

270

ENTER

RESET

PROG

RUN

OFF

INCH

SINGLE

STROKE

CONT

POWER

BRAKE

WARNING

HELP

1 2 3

4 5 6

9

8

7

.

0

CLEAR

SmartPAC 2

Wintriss Press Automation Control

F1

F2

F3

F4

F5

F6

F7

F8

Figure 3 - 1.  Front Panel, SmartPAC 2 with WPC Integration

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments