manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 176 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 176

1126800 

SmartPAC 2 with WPC Integration

Page 154

Chapter 2

Installing SmartPAC 2 and WPC

 Test for One-hand Control with “Light Curtain Break” Mode

NOTICE

Refer to “Switch 3 – One-hand Control or Foot Switch Mode,” page 243 and “’Light Curtain
Break’ Mode,” page 378

In “light curtain break” mode, you must break the light curtain with your hands, and then
push the one-hand control button within eight seconds of removing your hands from the light
curtain.  If you do not push the button within eight seconds, the press will not cycle.  Test
“light curtain break” mode as follows.

1.

 

Set Press Option switch 3 to CLOSED.  This enables “light curtain break” one-hand
operation. Power down, then power up SmartPAC 2 with WPC to enable the change.

2.

 

Set the STROKE SELECT switch to OFF and set the MODE to ONE HAND.  Set the
STROKE SELECT switch to SINGLE STROKE.

3.

 

On the WPC control board, the “Continuous selector” LED should be off, the “Single
Stroke selector” LED should be on, and the “One-hand selector” LED should be on.

4.

 

Without breaking the light curtain, depress the One-hand Control.  The press should not
cycle.

•

If the press does not cycle, go to the next step.

•

If the press cycles, check the wiring and make sure Press Option Switch 3 is set to
CLOSED and the MODE is set to ONE HAND.  Repeat the test.  If the press still
cycles, call Wintriss Tech Support.

5.

 

This time, break the light curtain with your hand or another object.  Remove your hand
from the light curtain and immediately depress the One-hand Control button.  The press
should cycle.

•

If the press cycles, go to the next step

•

If the press does not cycle, check the wiring and make sure Press Option Switch 3 is
set to CLOSED and the MODE is set to ONE HAND.  Repeat the test.  If the press
still does not cycle, call Wintriss Tech Support.

6.

 

Now break the light curtain with your hand.  Remove your hand from the light curtain
and wait ten seconds, timed with a watch or timer, before you depress the One-Hand
Control button.  The press should not cycle.

•

If the press does not cycle, you have completed the “light curtain break” test.  Go to
the next section and complete the test without “light curtain break.”

•

If the press cycles, check the wiring and make sure Press Option Switch 3 is set to
CLOSED and the MODE is set to ONE HAND. Repeat the test.  If the press still
cycles, call Wintriss Tech Support.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments