manualshive.com logo in svg

Honeywell SmartPAC 2, User Manual, Page: 129 / 522

Share
Download
Honeywell SmartPAC 2 User Manual Download Page 129

SmartPAC 2 with WPC Integration

1126800

Installing SmartPAC 2 and WPC

Chapter 2

page 107

Set Top Stop Angle and Install Overrun Magnet

DANGER

!

INJURY DURING SETUP

Keep all personnel away from the press during setup.

Ensure that there is no die or other tooling in the press during setup.

Failure to comply with these instructions will result in death or serious injury.

First, you will set the Top Stop Angle so that the press stops accurately at the top of the
stroke.  Then, you will install the magnet for the overrun limit switch.

Top Stop Angle is the point in the stroke at which the top-stop cam turns on.  Follow the
instructions below to determine the correct Top Stop angle and set it for your press.

NOTICE

RE-ADJUSTING TOP STOP ANGLE

If you have previously set up your press and set the Top Stop Angle, skip the next section
and start with “Prepare to Determine Top Stop Angle.”

Set Top Stop Angle for the First Time

NOTICE

If you have already set the Top Stop Angle at least once on this WPC on this press, go to
the next section.

The first time you set up the WPC control on your press, enter an initial value for Top Stop
Angle of 270

°

.

1. In Run mode (see page 325), select PRESS CONTROL.  Select the Top Stop Angle value

on the menu that appears.

2. Now set the Top Stop Angle value to 270

°

 by pressing the up or down cursor keys as

needed. When “270” appears, press RESET and go to the next section.

NOTICE

Use this value, 270

°

, as the “Old Top Stop Angle” in the instructions below.

Go to the next section.

Summary of Contents for SmartPAC 2











































































































































































































































































































































































































































































































































Reviews:

No comments