Honeywell RTY Series Installation Instructions Manual Download Page 1

 

 

 

Sensing and Control 

 

GENERAL INFORMATION 

The RTY Series uses a magnetically biased, Hall-effect 
integrated circuit (IC) to sense rotary movement of the actuator 
shaft over a set operating range. Rotation of the actuator shaft 
changes a 

magnet’s position relative to the IC. The resulting 

flux density change is converted to a linear output.  

MOUNTING INFORMATION 

Mount the sensor using the two easily accessible mounting 
holes and non-magnetic stainless steel M5 screws with flat 
washers. Mounting screw tightening torque is 2,5 N m 
±0,5 N m [22.1 in lb ±4.4 in lb]. In harsh applications, treat the 
screw threads with a suitable thread locking compound.

 

 

Table 1. Specifications

 

Characteristic 

Parameter 

LV (Low Voltage) 

HV (High Voltage) 

Supply voltage 

5 ±0.5 Vdc 

10 Vdc to 30 Vdc 

Supply current 

20 mA max. 

32 mA max. 

Supply current (during output to ground short) 

25 mA max. 

47 mA max. 

Output 

0.5 V to 4.5 V ratiometric 

0.5 V to 4.5 V non-ratiometric 

Output signal delay 

4 ms typ. 

Overvoltage protection 

10 Vdc 

 

Reverse polarity protection 

-10 Vdc 

-30 Vdc 

Output to ground short circuit protection 

continuous 

Output load resistance (pull down to ground)  

10 kOhm 

EMI: 

radiated immunity 
conducted immunity 

 

100 V/m from 200 MHz to 1000 MHz per ISO11452-2 

100 mA BCI per ISO11452-4 

from 1 MHz to 200 MHz 

100 mA BCI per ISO11452-4 

from 1 MHz to 400 MHz 

EMC 

exceeds CE requirements 

Operating temperature range 

-40 °C to 125 °C [-40 °F to 257 °F] 

Storage temperature range 

-40 °C to 125 °C [-40 °F to 257 °F] 

Ingress protection  

IP67 according to DIN 40050 

Expected life 

35 M cycles  

Media compatibility 

heavy transportation fluids  

Housing material 

PBT plastic 

Shock 

50 G peak 

Vibration 

20 G peak tested from 10 Hz to 2000 Hz 

Resolution 

12 bit 

Termination 

AMP super seal connector 

Mechanical end stop 

no 

Approvals 

CE 

 
Figure 1. Mounting Dimensions (For Reference Only: mm/[in].) 

22,0

[0.87]

26,0

[1.02]

9,5

[0.37]

        5,35 DIA.

[0.21]

37

[1.46]

55

[2.17]

5,9

[0.23]

8,3

[0.33]

        15,50 DIA.

[0.61]

4,60

[0.18]

13,8

[0.54]

15,6

[0.61]

4,12

[0.16]

25

[0.98]

36,4

[1.43]

0  

A

C

B

Pin 1

Pin 2

Pin 3

        2,0 DIA.

[0.078]

        6 DIA.

[0.24]

        32,0 DIA.

[1.25]

0  

/2 

0  

/2 

R

T

Y

X

X

X

X

X

X

X

X

Y

Y

D

D

M

M

S

S

S

S

 

A

 = Left output: 0.5 Vdc 

B

 = Zero reference 

C

 = Right output: 4.5 Vdc 

Pinout 

N  

(North 

American) 

(European) 

 

Pin 1

 = VCC 

Pin 2

 = GND 

Pin 3

 = Output 

Pin 1

 = GND 

Pin 2

 = VCC 

Pin 3

 = Output  

NOTICE 

Ferrous or magnetic material 
within a 75 mm [2.95 in] radius 
from sensor center may affect 
sensor performance.

 

Summary of Contents for RTY Series











Reviews: