manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual, Page: 185 / 241

Share
Download
Honeywell ORBIT 7120PLUS User Manual Download Page 185

Orbit 7120plus/7190g User Guide

171

Application Plug-Ins (Apps)

Any apps that you are using can be turned off or on by scanning the following bar 
codes. Apps are stored in groups: Decoding, and Formatting. You can enable and 
disable these groups of apps by scanning that group’s 

On 

or 

Off

 bar code below. 

You can also scan the 

List Apps

 bar code to output a list of all your apps. 

Note:

You must reset your device in order for the apps setting to take effect.

EZConfig Cloud for Scanning Introduction

EZConfig Cloud for Scanning provides a wide range of PC-based programming 
functions that can be performed on a scanner connected to your PC. EZConfig 
Cloud for Scanning allows you to download upgrades to the scanner's firmware, 
change programmed parameters, and create and print programming bar codes. 
Using EZConfig Cloud for Scanning, you can even save/open the programming 
parameters for a scanner. This saved file can be e-mailed or, if required, you can 
create a single bar code that contains all the customized programming parameters 
and mail or fax that bar code to any location. Users in other locations can scan the 
bar code to load in the customized programming. 

* Decoding Apps On

Decoding Apps Off

* Formatting Apps On

Formatting Apps Off

List Apps

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments