manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

164

Orbit 7120plus/7190g User Guide

To see this example, align the scanner with the signature area (not with the bar 
code). 

Send the following IMGBOX command string after the button push:

Example:

IMGBOX245w37h55y.

Note:

Case is not important in the command string. It is used here only for clarity.

The following image is captured:

The IMGBOX commands have many different modifiers that can be used to change 
the size and appearance of the signature image output by the scanner. Modifiers 
affect the image that is transmitted, but do not affect the image in memory. Any 
number of modifiers may be appended to the IMGBOX command.

Note:

The IMGBOX command will return a NAK unless a window size (width and height) are 
specified. See 

H - Height of Signature Capture Area

 (page 166) and 

W - Width of 

Signature Capture Area

 (page 167).

IMGBOX Modifiers

A - Output Image Width

This option is used to size the image horizontally. If using this option, set the reso-
lution (R) to zero.

Example:

Image Width set to 200A:

Image Width set to 600A:

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

AAMP of America iSimple Operation Manual preview
iSimple
Brand: AAMP of America Pages: 6
ULTIMATE SPEED CARBON Assembly And Safety Advice preview
CARBON
Brand: ULTIMATE SPEED Pages: 19
Galeo ORION Instructions For Use Manual preview
ORION
Brand: Galeo Pages: 19
Quintex DS18B20 Operation Manual preview
DS18B20
Brand: Quintex Pages: 29
Yakima K800 Instructions Manual preview
K800
Brand: Yakima Pages: 8
Pivot DXB-B User Manual preview
DXB-B
Brand: Pivot Pages: 4
VTech Baby 546103 Instruction Manual preview
546103
Brand: VTech Baby Pages: 22
GE 2020168 Installation Instructions preview
2020168
Brand: GE Pages: 2
HBX ORC-0100 Installation Manual preview
ORC-0100
Brand: HBX Pages: 12
3M Multimedia Projector MP8755 Quick Start Manual preview
Multimedia Projector MP8755
Brand: 3M Pages: 2
Yakima StickUp Installation Instructions Manual preview
StickUp
Brand: Yakima Pages: 21
PASCO PASport PS-2143 Manual preview
PASport PS-2143
Brand: PASCO Pages: 2
Covidien Nellcor MAXA Instructions For Use Manual preview
Nellcor MAXA
Brand: Covidien Pages: 64
InfoCase Fieldmate Series User Manual preview
Fieldmate Series
Brand: InfoCase Pages: 4
Thule Kit 1429 Fitting Instructions Manual preview
Kit 1429
Brand: Thule Pages: 8
R&G ECC0344R Fitting Instructions Manual preview
ECC0344R
Brand: R&G Pages: 8
Becker Rhotheta SAR DF 517 Manual preview
Rhotheta SAR DF 517
Brand: Becker Pages: 28
Miche SWR RC38DX OLT Manual Of Maintenance And Use preview
SWR RC38DX OLT
Brand: Miche Pages: 24

Brands by name

Popular brands

Load more brands