Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 192

Page: 192 / 210

192

SCS Series Manual —

P/N 15712:L 7/18/16

AM2020/AFP1010 Control-By-Event

Operators

NOT

Operator: The NOT operator inverts the state of the operand (activated to deactivated OR deacti-
vated to activated).

Equation: NOT(Z2)

The control module will remain activated UNTIL the operand comes into alarm.

IF Software Zone 2 is in alarm,

THEN this control module will be deactivated.

XZONE

Operator: For

Cross Zone

operation, the XZONE operator

is used.

Equation: XZONE(Z23)

IF ANY combination of TWO or more initiating devices
(L1D1, L1D2, L1D3, L1D4) that have been programmed
(Control-By-Event) to this software zone (Z23) come into
alarm,

THEN this control module will be activated.

DEL

Operator: For delayed operation, the DEL operator is used.

Equation: DEL(HH.MM.SS HH.MM.SS (Z1))

Example:

L1M3 activates Forward Activating Zone 223 (Z223).

L1M2 CBE is: DEL(00.00.30 00.01.30 (Z223))

IF Z223 has been active for 30 seconds

THEN L1M2 will become active. L1M2 will stay active for 1 minute and 30 seconds.

L1M1

L1D4

NOT(Z2)

(Z2)

L1D3

L1D2

L1M3

L1D1

L1D4

Z23

(Z23 )

(Z23)

XZONE(Z23)

DEL(00.00.30 00.01.30 (Z223))

(Z223)

L1M3

Z223

L1M2

Delay

Duration

(optional)

Internal

Equation

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Search results

Summary of Contents for NOTIFIER SCS Series

Reviews:

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 192 / 210

Search results

Summary of Contents for NOTIFIER SCS Series

Reviews: