manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 11 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 11

SCS Series Manual —

 P/N 15712:L  7/18/16

11

Cautions and Warnings

About This Manual

1.4  Cautions and Warnings

This manual contains cautions and warnings to alert the reader as follows: 

1.5  Manual Conventions

In this manual:

• The term “NFS2-3030” refers to both the NFS2-3030 and NFS-3030 FACPs unless noted otherwise.

• The term “NCA-2” refers to both the NCA-2 and the NCA Network Control Annunciators unless otherwise noted.

• The term “NFS2-640” refers to the NFS2-640 as well as the NFS-640/E.

• The term “NFS-320” refers to the NFS-320 as well as the NFS-320E, NFS-320C, and CPU-320SYS. 

!

CAUTION:

INFORMATION ABOUT PROCEDURES THAT COULD CAUSE PROGRAMMING ERRORS, RUNTIME ERRORS, OR EQUIPMENT 
DAMAGE.

!

WARNING:

INDICATES INFORMATION ABOUT PROCEDURES THAT COULD CAUSE IRREVERSIBLE DAMAGE TO THE CONTROL PANEL, 
IRREVERSIBLE LOSS OF PROGRAMMING DATA OR PERSONAL INJURY.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments