Honeywell MP09 Series User Manual Download Page 9

8

EN

WATER CONDENSATION DRAINAGE

When there is excess water condensation inside the unit, the air conditioner stops running and

shows a warning light. This warning light indicates that the water condensation needs to be drained 

using the following procedures:

Manual Draining for AC & Dehumidifier Mode

Water may need to be drained in high humidity areas.

Continuous Draining for Dehumidifier Mode

While using the unit in dehumidifier mode, continuous 
drainage is recommended.

WATER CONDENSATION DRAINAGE

1.
2.

3.
4.
5.

6.

Unplug the unit from power source.
Place a shallow pan under the lower drain plug. 
See diagram.
Remove the lower drain plug.
Water will drain out and collect in the shallow pan.
After the water is drained, replace the lower drain 
plug firmly.
You can now turn on the unit.

1.
2.

3.

4.

5.

Unplug the unit from the power source.
Remove the upper drain plug. While doing this 
operation some residual water may spill so 
please have a pan to collect the water.
Connect the drain connector to a ¾” hose (not 
included). See diagram.
The water can be continuously drained through 
the hose into a floor drain or sink.
You can now turn on the unit.

Lower
Drain Plug

Shallow Pan
(Not included)

Water Drain Pipe

Upper
Drain Plug

Summary of Contents for MP09 Series












Reviews: