background image

PRODUCT DATA

® U.S. Registered Trademark
Copyright © 1997 Honeywell Inc.   •   All Rights Reserved

ML7295 Spring Return

Direct Coupled Actuators

APPLICATION

The ML7295 Spring Return Direct Coupled Actuator (DCA) is
a control motor that provides proportional control for dampers
or valves in heating, ventilation, and air conditioning (HVAC)
applications. The actuator accepts either a current or voltage
signal from any electronic controller to position the damper/
valve at any chosen point between fully open and fully closed.
For hydronic valve applications, a complete line of brackets
and linkages are available for mounting Honeywell DCAs on
globe valves and on Honeywell ball valves. The ML7295
provides an electronic feedback signal (0-10 Vdc). This
feedback signal provides indication of the motor output hub
position and can be used for rebalancing an external control
circuit.

FEATURES

Brushless DC motor achieves sophisticated control of
speed, torque and braking.

Provides 142 lb-in. (16 N•m) torque.

Mounts directly on 3/8 in. to 1 in. (9 to 25 mm) round
and 1/4 in. to 3/4 in. (6 to 18 mm) square shafts.

Self-centering shaft coupling minimizes installation
time.

Spring return direction is field-selectable to simplify
installation.

Manual override permits unpowered positioning to
simplify installation and troubleshooting. Deactivation
of interlock is manual or automatic when power is
restored.

Highly-visible position indicator facilitates setup,
checkout and troubleshooting.

Rugged, lightweight all-metal alloy housing provides
durability.

Integral conduit connection.

Integral adjustable range-stop.

Models available with 0-10 Vdc input signal.

Models available with 4-20 mA input signal.

Models available with adjustable zero and span.

Models available with two fully adjustable line voltage
auxiliary switches.

Contents

Applications ......................................................................

1

Features ...........................................................................

1

Specifications ...................................................................

2

Ordering Information ........................................................

2

Installation ........................................................................

3

Operation .........................................................................

6

Checkout ..........................................................................

7

129-237

Rev. 1, 10/97

63-2539-1

Summary of Contents for ML7295 Series









Reviews: