Honeywell MeshGuard CO2 IR User Manual Download Page 34 | Manualshive

Page: 34 / 59

background image

MeshGuard LEL IR & CO2 IR User’s Guide

34

6.4.

Diagnostic Mode Programming

You can enter a special programming mode from Diagnostic Mode in order to perform advanced

programming functions. These include:

•

Enable/disable radio

•

Enable STD or RTR

•

Return the instrument to original factory settings

•

Enable/disable audible and visible alarms

•

Note:

When the MeshGuard LEL IR or MeshGuard CO2 IR is in this programming mode, if you do

not make a change or press a key for 60 seconds, it reverts to the standard Diagnostic Mode.

Important!

After you make changes in Diagnostic Mode, it is recommended that you turn off the

instrument and turn it on again before using it. Enter this programming mode by first entering

Diagnostic Mode. This requires starting the instrument while holding [Y/+] and [MODE]. When you see

the Sensor Raw Count screen, hold [MODE] and N/- until you see “Pro” in the display, indicating that

you are in Programming Mode.

Step through the menus by pressing [N/-]. Exit by pressing [MODE], and then shutting off the

instrument and restarting it.

Note: Raw count for CO

2

sensor

shows “---” instead of a

value

«
...
32
33
34
35
36
...
»

Summary of Contents for MeshGuard CO2 IR




























































Reviews:

No comments

Related manuals for MeshGuard CO2 IR

Brand: Panasonic Pages: 73

Brand: Panasonic Pages: 12

Brand: Neat Pages: 30

Brand: i-PRO Pages: 18

Brand: Qvis Pages: 32

Brand: media-tech Pages: 2

Brand: Edimax Pages: 137

Brand: Qlight Pages: 12

Brand: Abus Pages: 2

Brand: Inter-m Pages: 12

Solar Outdoor Siren 2

Brand: Popp Pages: 6

Brand: i-PRO Pages: 2

Brand: Hanwha Vision Pages: 17

Brand: General Lock Pages: 6

Brand: FLIR Pages: 2

Brand: Smanos Pages: 15

TRANSCENDENT VTD-TND5RME

Brand: Vitek Pages: 8

Smart Business Security System

Brand: ZMODO Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands