background image

. . . . .

C O N F I G U R I N G   M A X P R O   N V R

Configuring the Cameras

MAXPRO NVR 5.0 Installation and Configuration Guide

173

Figure 6-44    SMART VMD Configuration

Note:

You can draw a maximum of 10 ROIs (includes 

Include

 and 

Exclude

 

regions).

Include

 regions are shown as green rectangles and 

Exclude

 regions are 

shown in red rectangles in the field of view. 

Each region is assigned a unique identifier number for easy identification.

The Exclude region overwrites the Include region. No motion is detected in 
the area that is inside any of the exclusion regions.

6.

Under 

Alarm Settings

Type the 

Hold Time (sec)

. This indicates the hold time for the motion video after the 

detected motion stops. When motion is detected and motion video has started being 
recorded, if motion stops briefly and then resumes within 

Hold Time (sec)

, no 

“Motion stopped” event is generated. This brief gap in detected motion is ignored 
and motion triggered recording continues without interruption. On the other hand, if 
motion stops and no new motion is detected within 

Hold Time (sec)

, then the 

“Motion stopped” event is reported. Motion triggered recording is then stopped after 
additional Post-Alarm duration. The 

Hold Time

 range is 

to 

30

 seconds.

The 

Object Size Threshold 

(the minimum object size required to trigger an alarm) is 

displayed as a yellow rectangle in the field of view. Click and drag the corners of the 
rectangle to resize the minimum object size for motion detection.

Note:

The Object Size Threshold is a universal threshold across the entire image. By
default, the 

Object Size Threshold

 is set to the smallest size, and therefore even

very small motions trigger an alarm. This may not be appropriate for all sites and
cameras, and the yellow rectangle size should be adjusted if the default size is
not adequate.

Tip: 

Click the 

Refresh Image 

button to refresh the video.

Summary of Contents for MAXPRO NVR Hybrid PE









































































































































































































































































































































































Reviews: