manualshive.com logo in svg

Honeywell MAXPRO NVR Hybrid PE, Hardware Installation And Configuration Manual

Share
Download
Honeywell MAXPRO NVR Hybrid PE Hardware Installation And Configuration Manual Download Page 160

C O N F I G U R I N G   M A X P R O   N V R

Configuring the Cameras

160

 MAXPRO NVR 5.0 Installation and Configuration Guide

6

2.

Click the 

Camera

 tab to open the 

Camera

 page.

Figure 6-35    Camera page

Note:

All analog cameras that are pre-configured in the factory image appear in the
Camera page when you first open it.

3.

Under the 

Camera

 pane, select a camera to change the default parameters for the 

following settings.

•

Enable/Disable

 - Enables or disables a camera for recording and live video. By 

default the check box corresponding to a camera to enable live video preview is 
selected. To disable live video preview, clear the check box corresponding to a 
camera. The live video appears under 

Video Preview

 at the bottom right corner of 

the 

Camera

 page. 

•

Number

 - Displays the camera number. You cannot modify the camera number.

Summary of Contents for MAXPRO NVR Hybrid PE









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands