manualshive.com logo in svg

Honeywell MAXPRO NVR Hybrid PE, Hardware Installation And Configuration Manual

Share
Download
Honeywell MAXPRO NVR Hybrid PE Hardware Installation And Configuration Manual Download Page 119

. . . . .

C O N F I G U R I N G   M A X P R O   N V R

Configuring the System Settings

MAXPRO NVR 5.0 Installation and Configuration Guide

119

Under 

Email Settings

•

Type the 

From

 address

•

Type the 

SMTP Server Name

. 

•

The 

Port

 displays by default. Type a new 

Port

 number as applicable. 

•

Type the 

User Name

 of the user. 

•

Type the 

Password

 of the user.

•

Select the 

Use Default Credentials

 check box if you want to use the credentials that 

are used while logging on.

•

Select the 

Stop Email Service 

check box, if you do not want to send an email from 

the configured settings.

•

Select the 

Enable SSL

 check box.

Site Info Settings

Site Info settings allows you to quickly provide or refer the information related to Part Number, 
Serial Number, Voucher Number/System ID and the type of license being used to a support 
focal.

Note:

For MAXPRO NVR turnkey solutions shipped with v4.0 or later version, the Site
Info details are configured in the factory.

Under 

Site Info

•

Type the 

Part Number

 of the NVR box. If the field is empty, the part number can be

input without any credentials. To modify the Part Number, click 

 and then type 

the factory password provided by Honeywell Technical Support.

•

Type the 

Serial Number

. To modify the Serial Number, click 

 and then type the 

factory password provided by Honeywell Technical Support.

•

The 

Voucher Number/System ID

 is displayed by default and it is non-editable.

•

The 

License Type

 details are displayed by default and it is non-editable.

•

Under 

Notes 

type any required information regarding the site based on your 

requirements.

Archival Schedule Settings

The Archival Schedule settings enables you to configure the archiving schedule for your 
recordings. Ensure that the storage drive (NAS or SAN or USB) is configured in 

Disk

 tab and 

select the Drive Purpose as Archival. See 

Configuring the Disk Management Settings 

section 

on page 

122

 for more information.

Under 

Archival Schedule

•

Click 

Auto [24/7] 

option to archive the recordings automatically 24/7.

Or
Click 

Every Day at 

option

 

to select the required time for archival from the drop-down 

list.

Summary of Contents for MAXPRO NVR Hybrid PE









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands