Honeywell HTRD400 Reference Manual Download Page 31

Page: 31 / 176

HTRD400 System Reference Guide

Rev 1.02

Document 900.0328

05/05

Figure 2-6

HTCD50 Digital Camera Components

Position the four screw holes and one cable hole as desired:

Use the mounting template (see

Figure 2-7

) or the camera base to mark and then

pre-drill the four holes.

Orient the template (or camera base) as close as possible to the desired camera
view to provide the most flexibility in aiming the camera.

Use the recommended hole size for the #10 x 1 inch self-tapping screws
provided.

Grommet

HTCD50 Digital Camera

HTCD52 Digital Camera

Cover

Window

Cover

Microphone
cable (optional)

#10 x 1 inch
self-tapping
screws (x4)

Microphone cable
(optional)

Note

Security screws
(x4) are held in
place by o-rings.

Top
window

Front
window

Summary of Contents for HTRD400

















































































































































































Search results

Summary of Contents for HTRD400

Reviews:

Honeywell HTRD400, Reference Manual, Page: 31 / 176

Search results

Summary of Contents for HTRD400

Reviews: