Honeywell HPF-PS10 Instruction Manual Download | Manualshive

Page: 31 / 52

background image

HPF-PS Series Instruction Manual —

P/N LS10227-003HP-E:C 2/2/2022

31

Section 4: LED Indicators

The HPF-PS power supply has 3 system LED indicators for Power, Batt/Chgr Fault, and Ground Fault. In addition, each available output cir-
cuit also has 2 status LEDs. Refer to Figure 1.1 on page 11 for LED locations. A description of each HPF-PS LED indication is given below.

Ground Fault LED (yellow)

No Fault

LED is OFF

Fault Condition:
ground fault

LED is ON constant

Power LED (green)

No Fault

LED is ON constant

Fault Condition:
AC power loss (or brownout)
1 short blink (250ms)

Repeating LED blink pattern (non-diagnostic phase and diagnostic phase)

*Retrofit Mode will be indicated by an LED blink on the NAC1 Trouble LED only.

Battery fault LED (yellow)

No Fault

LED is OFF

Fault Condition:
Charging path (FETs) failure
1 short blink (250ms)

Repeating LED blink pattern (non-diagnostic phase and diagnostic phase)

Fault Condition:
Charger voltage too low or
Charger Diode Fault
2 short blinks (250ms)

Repeating LED blink pattern (non-diagnostic phase and diagnostic phase)

Fault Condition:
Battery
discharged/overcharged
3 short blinks (250ms)

Repeating LED blink pattern (non-diagnostic phase and diagnostic phase)

Fault Condition:
Battery disconnected/fully
discharged
4 short blinks (250ms)

Repeating LED blink pattern (non-diagnostic phase and diagnostic phase)

*Retrofit Mode will be indicated by an LED blink on the NAC1 Trouble LED only.

250ms 250ms 250ms 250ms 250ms 250ms 250ms 250ms

1000ms

Retrofit Mode*

pause

1000ms

250ms 250ms 250ms 250ms 250ms 250ms 250ms 250ms

1000ms

Retrofit Mode*

pause

1000ms

250ms 250ms 250ms 250ms 250ms 250ms 250ms 250ms

1000ms

pause

1000ms

Retrofit Mode*

250ms 250ms 250ms 250ms 250ms 250ms 250ms 250ms

1000ms

pause

1000ms

Retrofit Mode*

250ms 250ms 250ms 250ms 250ms 250ms 250ms 250ms

1000ms

pause

1000ms

Retrofit Mode*

«
...
29
30
31
32
33
...
»

Summary of Contents for HPF-PS10





















































Reviews:

No comments

Related manuals for HPF-PS10

Brand: Palmgren Pages: 20

Brand: Gechter Pages: 60

Brand: VONROC Pages: 84

Brand: Akyga Pages: 4

Brand: BE QUIET! Pages: 51

Brand: X-FLOC Pages: 51

Wireless Power Supply RS24E-424N-PU Series

Brand: B&PLUS Pages: 2

ILUEST NE Series

Brand: Salicru Pages: 60

Brand: FACHOWIEC Pages: 4

Brand: Cornwell Tools Pages: 4

Brand: Toolson Pages: 208

PowerGrip II LC 60

Brand: Metabo Pages: 32

Brand: EKSMA OPTICS Pages: 13

RINV500 PowerSource

Brand: Ring Powering Pages: 2

Brand: Central Pneumatic Pages: 17

HOT PRESS HGP220

Brand: Drytac Pages: 19

Brand: HYCON Pages: 26

Brand: Black & Decker Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands