Honeywell HPF-PS10, Instruction Manual

Page: 15 / 52

HPF-PS Series Instruction Manual —
P/N LS10227-003HP-E:C 2/2/2022 15
Addressable Module Mounting Installation
2.3 Addressable Module Mounting
The HPF-PS has been designed to allow the mounting of an addressable control, relay, or monitor module on the main circuit board inside
the power supply cabinet. This allows power to be fed from an HPF-PS output circuit directly to the module, if needed, without running the
power wires outside the cabinet. Remove mounting screws from the positions indicated below and replace with standoffs (included in hard-
ware kit). Mount the module over the standoffs and secure with screws.
Compatible modules include the XLS-CM-N(CDN), TC810N1013(CDN), XLS-MM-D(CDN), XLS-MM-A(CDN), TC809D1004(CDN),
TC809A1059, TC809A1067CDN, XLS-CM-R(CDN), TC810R1024(CDN), TC822A1010, XP6-C(A), XP6-R(A), and XP10-M(A).
TB4
TB15
T
B
2
T
B
1
O
U
T
6
O
U
T
5
O
U
T
4
O
U
T
3
O
U
T
2
O
U
T
1
NAC1
AUX1
NAC2
AUX2
O
U
T
6
O
U
T
5
O
U
T
4
O
U
T
3
O
U
T
2
O
U
T
1
NAC1
AUX1
NAC2
AUX2
A
-
B
+
B
-
A
+
A
-
B
+
B
-
A
+
A
-
B
+
B
-
A
+
A
-
B
+
B
-
A
+
A
-
B
+
B
-
A
+
A
-
B
+
B
-
A
+
*If the SLC device does
not match the one in this
figure, refer to the SLC
manual wiring conver-
sion charts for legacy
and newer versions of
the modules.
Figure 2.4 Mounting a Single Module in the HPF-PS Cabinet
Install stacked standoffs
(0.5” + 1.093” M/F)
– +
– +
– +
– +
– +
– +
– +
– +
– +
– +
– + – +
T1 0
J1
BA SE AD DR ES S+ 0 BA SE AD DR ES S+ 1 BA SE AD DR ES S+ 2 BA SE AD DR ES S+ 3 BA SE AD DR ES S+ 4 BA SE AD DR ES S+ 5
SW 1
T1
+1
+0
+2
+3 +4 +5
T0
T2 T3 T4 T5
T1 1
T1 2 T1 3 T1 4 T1 5
T1 6
0
1
2
3 4
5
6
7
8
9
1
0 1
1
1
3
1
4
1
5
1
2
0
1
2
3 4
5
6
7
8
9
AC AC 1 2
TB
4
TB15
T
B
3
T
B
2
T
B
1
O
U
T
6
O
U
T
5
O
U
T
4
O
U
T
3
O
U
T
2
O
U
T
1
O
U
T
6
O
U
T
5
O
U
T
4
O
U
T
3
O
U
T
2
O
U
T
1
A-
B+
B-
A+
A-
B+
B-
A+
A-
B+
B-
A+
install 1.093” M/F
standoffs
Note: For instructions on mounting a multi-module and a ZNAC-PS module, refer
to the
ZNAC-PS Install Sheet #LS10228-000GE-E.
The multi-module must be installed upside down when the ZNAC-PS is installed. If
the ZNAC-PS is not installed, the multi-module may be mounted in either direction.
Figure 2.5 Mounting a Multi-Module in the HPF-PS Cabinet