READ AND KEEP THIS
OPERATION MANUAL
•S
im
ple to insta
ll
Operation
Manual
• 1/3" Sony Super HAD CCD
• High Resolution:550 TV Lines
• 4 - 9mm DC Vari-focal Auto Iris
• Auto White Balance
• AGC, BLC, Flickerless On/Off
• Extra Video Output for Installer
• 3-Axis Camera Construction
• Vandal-Resistant Dome Housing
• Diameter of Bubble:100mm
HD51
Series
SPECIFICATIONS:
DIMENSIONS(mm):
COMPOSITION:
Model
Signal System
Scanning System
Scanning Frequency (H)
Scanning Frequency (V)
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity
Electronic Shutter
White Balance
AGC
BLC
Flickerless
Input / Output Connector
Power Consumption
Dome Size (Ø)
Weight
NTSC PAL
NTSC : 525 Lines PAL : 625 Lines
2 : 1 Interlace
15.734kHz 15.625kHz
59.94Hz 50Hz
1/3" SONY Super HAD CCD
410K / 380K 470K / 440K
More than 50dB (AGC Off)
550 TV Lines
1.0 Vp-p (75 Ohms, composite)
Fixed Lens : f=4.0mm
Manual
Internal
0.3 Lux
1/60 ~ 100,000 Sec. 1 /50 ~ 100,000 Sec.
Auto
On / Off
On / Off (with Slide Switch)
On / Off (with Slide Switch)
Power, Video
12VDC (10V~15V) / 3W (Max)
100mm
Approx. 844g
INSTALLATION:
Draw out power / video wires
to the connecting places.
3
Stick the guide pattern on the
wall or ceiling.
1
Adjust desired focus and scene
by turning and moving the
3-axis camera bracket by hand.
5
Drill four holes according to
the guide pattern then insert
anchors into the drilled holes.
2
Put the dome cover over the
base.
6
Fix the dome cover on the base
by L-Wrench.
7
Fix the camera to a celling using
four screws.
4
You must be fully aware of all the distinctive
features and precautions related to this
camera before installing it.
Built-in camera
bracket makes it much
easier to rotate in any
direction.
3-axis
CAMERA SET-UP:
Vari-focal Lens Type
DC Level Adjustment V.R
a
Function Selection Switch:
•FL(Flickerless) ON/OFF
•AGC(Auto Gain Control) ON/OFF
•BLC(Back Light Compensation)
ON/OFF
Service Monitor Connecter:
Use service monitor connector
to set camera angle & focus
when installing.
b
c
The image does not
appear on the screen.
Check the power source for the monitor and camera
and ensure that the voltage and polarity are properly
connected and being supplied correctly.
The image on the
screen is dim.
Check if the lens is stained. If dirty, clean the lens with
a soft, clean cloth.
Adjust the Back Focus of the lens again.
The camera does not work
properly, the surface of the
camera case is hot, and a black
line appears on the screen.
Check if you have connected the camera to a proper
power source and If there is no problem with the power,
turn the unit off immediately and seek assistance from
our Customer Service department.
The screen blinks a lot.
Check if the camera is pointed toward the sun or a
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
NAME AND FUNCTION:
Vari-focal Lens Type
BLC
AGC
FL
ON
OFF
ON
DC LEVEL
VIDEO
SWITCH
ON
3
1
2
AC 24V
J503
J504
AC24V
J501
J502
HE
AT
ER
/AUD
IO
J5
05
a
b
c
Operation Manual
Guide Pattern
Service Monitor Cable
75.7
100.0
142.4
101.0
37.0
47.15
Ceiling
Mounting Screw
L-Wrench
L-Wrench
Guide Pattern
Dome Base
Mounting
Screw
Dome Cover
P/N:3810-0055Q
Rev 0 05
/23
※
3/4 JIS B0202-1982
!
Do not install the camera in
extreme temperature conditions.
Do use the camera under conditions
where temperatures are within
-20
°
C to 45
°
C.
Be especially careful with ventilation
under high temperatures.
!
Do not drop the camera or
subject them to physical shocks.
It can cause malfunctions to occur.
!
Do not disassemble the camera.
There are no user-serviceable parts
inside it.
!
Note
When this camera is installed near
wireless communication devices
that emits strong electromagnetic
field, irregularity such as noise on
the monitor may appear.
PRECAUTIONS:
Design and specifications are
subject to change without notice.
Need Help?
Call 1.800.796.CCTV for sales, service and customer support.
www.honeywellvideo.com
CONNECTION:
No.
#1
#2
Function
Video Output
Power Input
Remark
1.0 Vp-p
12VDC, Max 3W/ 250mA
Terminal Color
Yellow
Red
Connecting to
Monitor and Power
12VDC Power Type
Camera Lay-out
#1
#2
Video
(Yellow)
Power
- 12VDC
(Red)
Video Output
GND
• The wire is polarized. • Use 12VDC power source.
Tilt rotation:
Adjusting the vertical angle.
Pan rotation:
Adjusting the horizontal angle.
Horizontal rotation: Adjusting the horizontal
position of the screen.
1
2
3
Focus handle: Focus (Far or Near)
Zoom handle: Zoom (Tele or Wide)
4
5
4
5
2
1
3
90º
360º
360º
