Honeywell HD4DIR User Manual Download Page 31

Page: 31 / 32

Document 800-01529 Rev A

02/08

Cable Guidelines

Maximum Power Supply Cable Length (feet/meters)
Cameras With AC/DC Power Supplies

Wire gauge

Total load

Optional
Power supply

24 AWG

22 AWG

18 AWG

16 AWG

2.5 W

15 VDC

260/79

415/126

1055/322

1680/512

2.5 W

24 VAC

608/185

980/299

2515/767

3930/1198

3.5 W

15 VDC

180/55

290/88

730/220

1170/352

3.5 W

24 VAC

470/143

760/232

1926/587

3065/934

Note

Calculations are based on an unregulated linear power supply, which would be the
worst case. Using a regulated or switching power supply can increase the cable
distance. Honeywell recommends using a

CSA Certified/UL listed Class 2

power

adapter to ensure compliance with electrical safety standards.

Maximum Video Coaxial Cable Length (feet/meters)

Cable type

RG-59

RG-6

RG-11

Wire gauge

23 AWG*

18 AWG*

16 AWG*

Maximum length (feet/meters)

750/229

1500/457

2000/610

* Copper clad steel core, 95% braided shield

Summary of Contents for HD4DIR

































Search results

Summary of Contents for HD4DIR

Reviews:

Related manuals for HD4DIR

Brands by name

Popular brands

Honeywell HD4DIR, User Manual

Search results

Summary of Contents for HD4DIR

Reviews:

Related manuals for HD4DIR

Brands by name

Popular brands