Document 800-13165 – Rev A – 11/2012
HC Series ONVIF True Day/Night
Network Box Camera
Quick Install Guide
Document
800-13165
– Rev
A
–
11/2012
Thank you for purchasing a Honeywell equIP Series HC True Day/Night
Network Box Camera. Before installing the camera, please read this guide
carefully and verify your model:
HCD2F 1080p resolution
HCD1F 720p resolution
HCW1F Wide Dynamic 720p resolution
For detailed information for your specific camera, please refer to the
appropriate user guide located on the IP Utility DVD.
http://www.honeywellsystems.com/
support/download-center/index.html
and follow the instructions on the
page to logon, find your camera, and then download software updates.
Warnings
Installation and servicing should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain your
warranty.
WARNING!
24 V AC models require the use of CSA Certified/UL
Listed Class 2 power adapters to ensure compliance
with electrical safety standards. Power over Ethernet
(PoE) should meet the IEEE 802.3 af PoE standard
.
FCC Compliance
Information to the User
: This equipment has been tested and found to
comply with the limits for a Class B digital device. Pursuant to Part 15 of the
FCC Rules, these limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference. For example, try
reorienting or relocating the receiving antenna, increasing the separation
between the equipment and receiver, or connecting the equipment to an
outlet on a different circuit.
Caution
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
North America
The equipment supplied with this guide conforms to UL 60950-1 and CSA
C22.2 No. 60950-1.
Europe
The manufacturer declares that the equipment supplied with this guide is
compliant with the essential protection requirements of the EMC directive
2004/108/EC and the General Product Safety Directive 2001/95/EC,
conforming to the requirements of standards EN 55022 for emissions, EN
50130-4 for immunity, and EN 60950 for Electrical Equipment safety.
Unpack Everything
Prepare for Installation
Select the lens to use with your camera. This equIP series IP Network
Camera supports the use of a manual iris or DC (Direct Drive) iris lens.
When using a DC iris lens, it should be connected to the camera via the 4-
pin square socket located at the side of the camera.
Mount the Camera
This camera is intended for indoor use. Mount the camera using a camera
bracket for indoor applications. If you choose to mount the camera
outdoors, you must employ a suitable weatherproof enclosure. See
for information on Honeywell weatherproof
enclosures and brackets.
Connect the Wiring
Note
For secure installations, protect surface mounted cables with
plastic or metal cable covers.
If your installation involves a 24 V AC power source, then
please wait approximately 60 seconds after connecting to a
power source for video to appear on the local video out.
WEEE (Waste Electrical and Electronic Equipment)
. Correct
disposal of this product (applicable in the European Union and
other European countries with separate collection systems).
This product should be disposed of, at the end of its useful life,
as per applicable local laws, regulations, and procedures.
•
One HC Camera
•
3-pin terminal block for power
input, and 4-pin terminal block for
alarm input/output
•
This guide
•
One DVD containing the
software and the User
Guide
24 V AC power
RJ45 Ethernet
network connection
(using 10Base T or
100Base TX cable).
Also for Power over
Ethernet (PoE
802.3 af).
Video monitor
Audio input/output
Alarm input/output
