Honeywell FlexLine SmartServo 954 Installation Manual Download Page 9 | Manualshive

Page: 9 / 45

Honeywell FlexLine SmartServo 954 Installation Manual Download Page 9

Part No: 4417341 Revision 10

Installation Manual 9
954 SmartServo FlexLine

2. SAFETY AND SECURITY

General

The 954 SmartServo FlexLine is a servo-based level gauge which is used in inventory
measurement systems. It can also be used to interface with other systems and sensors
such as pressure, density, or temperature sensors.

For the correct and safe servicing of this product, it is essential that all personnel follow
the generally accepted safety procedures in addition to the safety precautions specified in
this manual.

Safety Conventions

WARNINGS

The following warning symbol is used in this manual to urge attention in order to

prevent personal

injuries

or

dangerous situations

, further described in this manual.

Symbol

Description

Remark

General warning

Will always be explained by
text.

CAUTIONS

The following caution mark is used in this manual to urge attention in order

to prevent

damages to the equipment

further described in this manual.

Symbol

Description

Remark

General caution sign

«
...
7
8
9
10
11
...
»

Summary of Contents for FlexLine SmartServo 954














































Reviews:

No comments