manualshive.com logo in svg

Honeywell Dolphin 99 EX, User Manual

Share
Download
Honeywell Dolphin 99 EX User Manual Download Page 193

17 - 5

Troubleshooting

If you encounter problems with your QuadCharger device, refer to chart below for possible solutions. 
If problems persist, please contact Honeywell Technical Support. 

Problem

Issue

The Status LED does not come on when I 
insert a battery pack.

Check the power connections; make sure the Power cable is 
inserted into the Power supply connector and the battery pack 
is properly seated.

The Status LED lights red during charging.

Try to charge the battery in one of the other charging slots. If 
the red Status LED comes on again, then the problem is 
associated with the battery pack. If the red status stays with the 
charging slot, the problem is associated with the charging 
circuitry.

The Status LED flashes red without a 
battery in the charging slot.

If a battery is in failure mode (flashing red LED), and that 
battery is removed from the charging slot, the slot does not 
reset and will continue to flash red. To reset the slot and stop 
the flashing red LED, insert a known good battery into the slot 
or recycle the power to the QuadCharger.

Summary of Contents for Dolphin 99 EX







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands