background image

8

DACT-E3 Product Installation Document —

 P/N 9000-0581:J6  12/16/2019

Section 4:  Formats and Codes

4.1 Formats

The DACT-E3 Digital Alarm Communicator Transmitter offers several formats that can be configured in CAMWorks. The DACT-
E3 uses the Ademco Contact ID format to transmit information to a Central Station. Table 4.1.1 lists the following DACT-E3 
functions:

4.2  DACT-E3 Contact ID Event Reporting Codes in CAMWorks

In the CAMWorks program, there are two types of formats used to configure the DACT-E3 Contact ID Event Reporting Codes.

4.2.1  Standard Formats

The DACT-E3 can be configured to allow each SLC device to report an event by selecting the DACT Reporting Feature. To 
define the Standard format for the ILI-E3/ILI95-E3 Series panel or SLP-E3 panel, enable the Standard Reporting Codes in 
the DACT Report Format Section of the DACT Settings screen in CAMWorks. The Custom DACT Reporting Feature is 
usually disabled by default. If you disable the Custom DACT Reporting Feature, the system uses the Standard Codes. For 
information on the DACT-E3 Contact ID Event Reporting Codes for Standard Formats, refer to Table 4.2.1.1. Figure 4.2.1.1 
illustrates an example of the DACT-E3 Contact ID Reporting Codes for Standard formats used to configure the following 
types of systems.

Figure 4.2.1.1   Example of the DACT-E3 Contact ID Event Reporting Codes for Standard Formats

Function

Description

Line seizure                                         

Takes control of the phone lines, disconnecting any premises phones using the same

lines. 

Off/On-Hook 

Performs on and off-hook status to phone lines

Listen for dial tone -

440 Hz tone typical in most networks.

Dialing the Central Station phone number   Programmable.
‘ACK’ and “Kiss-off” Tone

Discern proper Central Station "ACK" and "Kiss-off" tone

Transmits data  

Transmit data to the Central Station.

Data verification

Verify that data has been accepted by the Central Station

Phone line options

Hang-up and release phone lines. 

Communication Formats

Communicate in a variety of formats

Table 4.1.1 DACT-E3 Functions

Standard Format

Custom Format

S T A N D A L O N E  S Y S T E M S

C O N T A C T   ID  F O R M A T

E X A M P L E  

N O T E :  G r o u p  N u m b e r s  a r e  
t r u n c a t e d  t o  r a n g e  [ 0 0 - 9 9 ] .

[1 ]= N e w   E v e n t
[3 ]= R e s to ra l

E v e n t  T y p e  

N e w   E v e n t

 1

[ R ]

[ E E E ]

[ 0 0 ]

F ir e   A la r m  

 1 1 0

 0 0

N o t  U s e d

N o t  U s e d

C O N T A C T   ID  F O R M A T

G r o u p    

N u m b e r

R e s p o n s e  

T y p e

G r o u p   9 5

S m o k e   A la r m

S IN G L E - R IN G

N E T W O R K E D  S Y S T E M S

C O N T A C T   ID  F O R M A T

E X A M P L E  

 1

F ir e   A la r m

 1 1 0

 0 0

N e w   E v e n t

C O N T A C T   ID  F O R M A T

N o d e   2 5

M U L T I- R IN G  

N E T W O R K E D  S Y S T E M S

C O N T A C T   ID  F O R M A T

E X A M P L E  

[1 ]= N e w   E v e n t
[3 ]= R e s to ra l

E v e n t  T y p e  

N e w   E v e n t

 1

[ R ]

[ E E E ]

[ 0 N ]

F ir e   A la r m  

 1 1 0

 0 1

N o d e  

N u m b e r   1 0 0 s

C O N T A C T   ID  F O R M A T

N o d e    

N u m b e r  

1 0 s   &   1 s

R e s p o n s e  

T y p e

N o d e   1 0 3

[1 ]= N e w   E v e n t
[3 ]= R e s to ra l

[ R ]

[ E E E ]

[ 0 0 ]

E v e n t  T y p e  

N o d e    

N u m b e r

R e s p o n s e  

T y p e

N o t  U s e d

S m o k e   A la r m

S m o k e   A la r m

N O T E :  T h e   1 0 0 s  d ig it  o f  t h e  n o d e  
n u m b e r  is  r e p o r t e d  in  t h e   [ O N ]   f ie ld .

N o t  U s e d

[ N N

T ]

0 3

6

[ N N

T ]

[ G G

T ]

9 5

6

2 5

6

Summary of Contents for DACT-E3















Reviews: