background image

6

DACT-E3 Product Installation Document —

 P/N 9000-0581:J6  12/16/2019

2.4 Specifications

The following list the electrical specifications for the DACT-E3 sub-assembly.

Section 3:  Wiring Connections

Table 3.1 lists the field wiring connections for the DACT-E3. 

Operating Voltage:

24 VDC non-resettable 

Operating Current:

0.018 amp

Alarm Current:

0.018 amp

Operating Temperature:

32° to 120° F (0° to 49° C)

Relative Humidity:

0 to 93%, non-condensing at 90° F (32° C)

Supervised
Class 2 Power-Limited

Designation

Description

Comments

TB1-1

COM A IN

COM A from ILI-MB-E3/ILI95-MB-E3 TB3-1 or SLP-E3 TB3-1

TB1-2

COM B IN

COM B from ILI-MB-E3/ILI95-MB-E3 TB3-2 or SLP-E3 TB3-2

TB1-3

COM A OUT

COM A OUT to other devices

TB1-4

COM B OUT

COM B OUT to other devices

TB1-5

+24 V IN

+ 24 VDC from PM-9/PM-9G TB4-1, TB4-3, TB4-5 or SLP-E3 TB2-3                          

TB1-6

GND

GND from PM-9/PM-9G TB4-2, TB4-4, TB4-6 or SLP-E3 TB2-4

TB2-1

T1 Tip

Line 1 Tip IN from street Non power-limited*

TB2-2

T1 Ring

Line 1 Ring IN from street Non power-limited*

TB2-3

P1 Tip

Line 1 Tip OUT to phone Non power-limited*

TB2-4

P1 Ring

Line 1 Ring OUT to phone Non power-limited*

TB2-5

T2 Tip

Line 2 Tip IN from street Non power-limited*

TB2-6

T2 Ring

Line 2 Ring IN from street Non power-limited*

TB2-7

P2 Tip

Line 2 Tip OUT to phone Non power-limited*

TB2-8

P2 Ring

Line 2 Ring OUT to phone Non power-limited*

*Non power-limited

Table 3.1   DACT-E3 Installation Wiring Terminals

NOTE: 

For additional information on the DACT-E3, refer to the following document:

- E3 Series

®

 (Expandable Emergency Evacuation System) Control Panel UL Listing Document, P/N: LS10080-051GF-E

Summary of Contents for DACT-E3















Reviews: