background image

® U.S. Registered Trademark
Copyright © 2003 Honeywell International Inc.  •  

  • All Rights Reserved 

OWNER'S GUIDE

69-1525-2

CT500 Electronic Thermostat

Non-programmable Heat and/or Cool 

Low Voltage (20 to 30 Vac) Thermostat and Wallplate  

Model CT500

Congratulations on purchasing your new thermostat! 
More than 100 years of engineering expertise enabled 
this thermostat to provide you with a more comfortable 
and convenient living environment.

Direct any questions about this thermostat to the 
Honeywell Customer Relations Center at 

www.honeywell.com/yourhome

 or 1-800-468-1502, 

Monday  - Friday, 7:00 am - 5:30 pm, Central time.

MERCURY NOTICE

If this control is replacing a control that contains 
mercury in a sealed tube, do not place your old 
control in the trash. Dispose of it properly.

Contact your local waste management authority 
for instructions regarding recycling and the 
proper disposal of an old control. If you have 
questions, call Honeywell at 1-800-458-1502.

1 PREPARE FOR INSTALLATION

Check Table 1 to be sure this thermostat is compatible 
with your system. If not, return it to the retailer. For 
more information, call Honeywell at 1-800-468-1502.

Acquire tool and items as needed. See Fig. 1.

Fig. 1. Required installation tools and supplies.

M18920

CROSS-RECESSED
SCREWDRIVER

HAND OR POWER
DRILL WITH 3/16 INCH
DRILL BIT, IF NEEDED TO
DRILL HOLES IN WALL

WIRE CUTTER/STRIPPER OR SHARP
KNIFE, IF NEEDED TO STRIP WIRES

LEVEL, IF NEEDED TO LEVEL
THERMOSTAT FOR APPEARANCE

Summary of Contents for CT500









Reviews: