manualshive.com logo in svg

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 27 / 230

Share
Download
Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 27

27

Item LED

LED
State/Color

Description

4, 6,
8,
10

Ethernet Port
Link/ Active ( 
Lower LED)

Green
On/Off/
Blinking

On for connection; Off for no
connection; and blinking for activity

Hardware Configuration of EPM

Refer to the common

EPM

section.

Hardware Configuration of IO

Refer to the I/O module type section.

Device Replacement

ATTENTION: If Secure Communication is enabled in the system, the relative
information of the new CPM should be updated in the IPsec configuration of the
PC installed the ControlEdge Builder and IPsec should be configured and
enabled on the new CPM. For more information, see "Chapter 9 " in the

ControlEdge PLC and ControlEdge RTU Network and Security Planning Guide

.

Replacing a non-redundant or unsynchronized
primary PLC-CPM

ATTENTION: This procedure can only be performed while off-
process.
We recommend that you proceed with extreme caution
whenever replacing any component in a control system. Be
sure the system is offline or in a safe operating mode.
Component replacements may also require downloading
appropriate configuration data to the replaced component
through ControlEdge Builder.
Wear an ESD wrist strap and observe static precautions.

Before replacing a non-redundant or unsynchronized primary PLC-
CPM:

n

It is recommended to upload and SAVE a copy of the
configuration, or ensure that a previously saved copy of the

Summary of Contents for ControlEdge 900 platform







































































































































































































































Reviews:

No comments