Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 210

Page: 210 / 230

Appendix A - Installing RTP

Using Dual RTPs to field wiring the 32 Point DC DO

ATTENTION:

RTP and cables are intended for permanent installation within their own
enclosure.

32 point DC Digital Output is limited to 6A per RTP and 0.5A per output.

To wire the 32 Point DC DO using dual RTPs:

1. Mount the RTP cable assembly to ControlEdge 900 Controller. See the

following figure for the example installation diagram.

a. Remove the relevant key tabs from the terminal block to allow connection

with the module.

b. Connect the appropriate cable to the module at ControlEdge 900

Controller. Possible options are:

900RTC-3410 Remote Terminal Cable assembly, 1.0 meters long

900RTC-3425 Remote Terminal Cable assembly, 2.5 meters long

c. Install the module label onto the module connector cover.

210

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 210 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: