Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 207

Page: 207 / 230

Appendix A - Installing RTP

SDC+ refers to switched positive side of the DC supply.

Terminals 9 and 11 (DC-) are connected through the RTP cable. Same for
terminals 10 and 12 (DC-).

Using an RTP to field wiring the 8 Point AC DO

ATTENTION:

RTP and cables are intended for permanent installation within their own
enclosure.

8 point AC Output is limited to maximum of 2A per output for any VAC, 6A
per RTP for 240VAC, 8A per RTP for 120VAC.

The RTP combines the 8 isolated outputs into one group of 8.

To wire the 8 Point AC DO using an RTP:

1. Mount the RTP cable assembly to ControlEdge 900 Controller. See the

following figure for the example installation diagram.

207

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 207 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: