Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 196

Page: 196 / 230

Appendix A - Installing RTP

Table A-2: Analog Input accuracy specification

Range

AI Module Accuracy

RTP + Cable Accuracy

AI RTP Accuracy

100

Plat. RTD

±0.1% of Range

±0.04% Range (0.357°C)

±0.14% of Range

JIS RTD

±0.1% of Range

±0.12% Range (0.824°C)

±0.22% of Range

Cu. RTD

±0.1% of Range

±0.57% Range (1.540°C)

±0.67% of Range

200

OHMS

±0.1% of Range

±0.07% Range (0.140

)

±0.17% of Range

0-10mV LINEAR

±0.1% of Range

±0.04% Range (0.004mV)

±0.14% of Range

Using Dual RTPs to field wiring the 16 Point AI

ATTENTION:

RTP and cables are intended for permanent installation within their own
enclosure.

The RTP labeled “DI, DO, AO RTP ASSY” with jumpers J2-J9 is the correct
one for 16 point AI.

To wire the 16 Point AC AI using two RTPs:

1. Mount the RTP cable assembly to ControlEdge 900 Controller. See the

following figure for the example installation diagram.

196

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 196 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: