Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 191

Page: 191 / 230

Appendix A - Installing RTP

4. Connect field wiring, as shown below.

ATTENTION: Short connect terminal 30 and 31 as shown in the diagram
above.

See "Terminal Block-to-Field (Signal) Wiring" on page 106 for more
information.

Using an RTP to field wiring the UAI

ATTENTION:

RTP is not for use with thermocouples.

RTP and cables are intended for permanent installation within their own
enclosure.

To wire the UAI using an RTP

1. Mount the RTP cable assembly to ControlEdge 900 Controller. See the

following figure for the example installation diagram.

191

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 191 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: