manualshive.com logo in svg

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 180 / 230

Share
Download
Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 180

n

Equipment shall be installed in compliance with the enclosure,
mounting, spacing and segregation requirements of the ultimate
application.

n

For installation with a second active phase (L-L) instead of neutral
(L-N) connection both phases must be protected externally with
circuit breaker adequately rated for 3 A maximum and 250 V AC
minimum.

For Canada

n

The installer shall provide transient over-voltage protection
external to the apparatus such that the voltage at the supply
terminal of the apparatus does not exceed 140% of the voltage
rating of the equipment.

n

The equipment shall be mounted in an enclosure providing a
minimum degree of protection of IP54 in accordance with
CAN/CSA 60529., and in a tool-secured enclosure which meets the
requirements of CAN/CSA 60079-0 and CAN/CSA 60079-15.

n

Equipment shall be installed in compliance with the enclosure,
mounting, spacing and segregation requirements of the ultimate
application.

For ATEX

n

The installer shall provide transient over-voltage protection
external to the apparatus such that the voltage at the supply
terminal of the apparatus does not exceed 140% of the voltage
rating of the equipment.

n

The equipment shall be mounted in an enclosure providing a
minimum degree of protection of IP54 in accordance with
EN/IEC 60079-15.

n

The equipment shall be mounted in a tool-secured enclosure
which meets the requirements of EN/IEC 60079-0 and EN/IEC
60079-15.

n

The equipment shall be used in an area not more than Pollution
Degree 2 as defined in EN/IEC 60664-1.

180

Chapter 9 - Special Condition of Use and Approved Standards

Summary of Contents for ControlEdge 900 platform







































































































































































































































Reviews:

No comments