Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 172

Page: 172 / 230

Figure
Item

LED

LED State/Color

Description

Module
Status LED

Solid Orange

Boot

Blinking Red at 1 Hz

System in running state with
error

Blinking Red at 0.5 Hz

Module offline or
unconfigured

Solid Green

System good in running state
without error.

Blinking Green and
Orange at 0.5 Hz

Firmware Upgrade

RS232 LEDs

Blinking Orange

Blingking Green

Blinking Yellow

TX and RX

OFF

No communication

RS485 LEDs

Blinking Orange

Blingking Green

OFF

No communication

I/O Indicators

The following diagram displays the location of the LED indicators on
the I/O modules. The table below explains the meaning of each LED
state.

Figure 8-2: I/O Indicators

172

Chapter 8 - Diagnostics and Troubleshooting

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 172 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: