Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 171

Page: 171 / 230

171

Item

LED

LED
State/Color

Description

Role

Green

Other situation except
booting

OFF

EPM is booting

3, 5

Ethernet Port
Speed ( Upper
LED)

Yellow On/Off

OFF for 10Base-T; ON for
100Base-TX.

4, 6

Ethernet Port
Link/ Active (
Lower LED)

Green
On/Off/
Blinking

OFF for no connection; ON
for connection; Blinking for
toggle

Serial Communication Module Indicators

The following diagram displays the location of the LED indicators on
the serial communication module:

The table below explains the meaning of each LED state:

Table 8-2: Serial Communication Module Indicator Definition

Chapter 8 - Diagnostics and Troubleshooting

Summary of Contents for ControlEdge 900 platform







































































































































































































































Search results

Summary of Contents for ControlEdge 900 platform

Reviews:

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 171 / 230

Search results

Summary of Contents for ControlEdge 900 platform

Reviews: